A 3D printer made mostly of plastic bricks sounds like a toy with a stepper motor bolted on. Studprint, an open-source design from University of Waterloo mechatronics engineering student Adam Turaj, is more than that. It is a standard bedslinger FDM machine whose frame, motion system and extruder are, by the author's count, 92% LEGO bricks, and it has printed a recognizable Benchy in about 1.25 hours using Klipper. Tom's Hardware reported on the project on November 14, putting the full bill of materials at $173.35, of which about $30 is LEGO.

The interesting part is not the novelty. It is how far a deliberately constrained parts list can be pushed before the physics start to object, and where the designer drew the line.

A Hack Club Challenge With a $350 Ceiling

According to the repository README, Studprint began as a response to Hack Club's "Infill" You Ship, We Ship (YSWS) challenge, in which participants build a 3D printer for under $350. Turaj, who grew up with LEGO, decided to make the entire printer out of it. Tom's Hardware reports that Infill offered makers a $350 grant, that submitting a Benchy gave participants a chance to be flown to the Rocky Mountain RepRap Festival 2026, and that Turaj was one of them. He presented Studprint there to more than 4,000 people, according to the same report.

Finishing at roughly half the allowed budget is notable in itself. The $173.35 bill of materials is just under 50% of the $350 grant, and the LEGO portion, about $30, is a small slice of that total.

What "92% LEGO" Actually Means

Percentages like this invite skepticism, so it is worth being precise about how the number was derived. The README states that the 92% figure is calculated as the number of LEGO components divided by the total number of components reported in the BOM within the project's SolidWorks drawings. It is a part count, not a measure of mass, cost or structural load. Tom's Hardware puts the non-LEGO count at only 13 parts.

Turaj also set himself a stricter rule than "anything with the LEGO logo." The README says he defined classical LEGO as the bricks and parts that interface with them, meaning no Technic, and used it wherever possible. The exceptions are acknowledged up front: custom mounts for the stepper motors, electronics and other hardware cannot realistically be made under that limitation.

The project's build journal, which starts on February 13, 2026, is candid about where purity gave way to practicality. By Day 13, on February 26, the X axis was finished and almost entirely LEGO, apart from mounts for the hot end, the BLTouch probe and a leadscrew adapter. The motion relies on LEGO worm screws, which Turaj notes are technically Technic parts but could not be avoided. He wrote that he had originally not planned to use LEGO for the motion platform at all.

Motion From Bricks and Worm Screws

Building linear motion out of LEGO is the hard problem here. The journal shows Turaj confronting exactly that. The Y axis is a single linear rod paired with a LEGO leadscrew, and he wrote that he was a little concerned about the up-play, the vertical slop a one-rod carriage can allow. He also worried that the top of the Z axis would not be stiff enough, noting that it was difficult to stiffen further because of the limitations of LEGO.

The final build phase, which the journal dates from March 16 to April 19, brought fixes. Turaj added two wheels to buff up the X axis, added an extra wheel at the bottom of the X rail because the toolhead had too much rotational play, and reinforced the YZ mounts. Tom's Hardware notes that even the build plate is a block of LEGO, and that the leadscrews are all LEGO pieces.

Advertisement

The Extruder Redesign

The extruder is where the all-brick idea gave ground most visibly. The journal's first entry describes a plan to use LEGO parts and a rubber band as the idler. After the build, though, Turaj wrote that the LEGO wheels could not grip the filament well enough, and that friction from the Bowden tube and hot end made extrusion impossible. He ditched the LEGO wheel concept for BMG dual extruder gears and a spring tensioner, which still uses some LEGO parts. At the festival he hit further trouble with the Bowden tube kinking and a bad filament path, and rotated the extruder 90 degrees to give the tube more room to compress.

That history is worth keeping in mind when reading the "92%" figure, which counts parts rather than function.

The Non-LEGO 8%

The electronics are conventional and sensible for a budget Klipper build. Per Tom's Hardware, Studprint uses a BTT SKR Pico V1.0 control board, a Raspberry Pi Zero 2 W for wireless capability, and a Mean Well LRS-150-24 power supply, with each of the three priced at around $25. Motion comes from five NEMA 17 stepper motors, four for the axes and one to feed filament to a Trianglelab V6, which Tom's calls an extruder.

Advertisement

None of that is exotic, which is the point. A maker could source the same electronics for any other small printer. The LEGO structure is what changes.

One Benchy, 1.25 Hours

The evidence of performance is thin but real. Tom's Hardware says the only print shown on the GitHub repository is a Benchy, sliced in Klipper and printed in 1.25 hours, and calls the result surprisingly good considering the leadscrews are all LEGO pieces. The journal likewise records a successful Benchy in about 1.25 hours after Klipper was set up.

It is also a single data point. Neither the repository README nor Tom's report offers dimensional accuracy figures or long-run reliability results, and the festival extruder problems suggest the design was still being sorted out. Readers should treat Studprint as a convincing proof of concept rather than a replacement for a commercial bedslinger.

What It Means for Makers

The design is genuinely open. The repository includes a CAD folder and a BOM.xlsx spreadsheet, and the hardware is released under the CERN Open Hardware Licence Version 2, Strongly Reciprocal (CERN-OHL-S-2.0), which is designed to keep modified versions open under the same terms. That makes Studprint a legitimate base for remixes rather than a look-but-don't-touch showpiece.

There are caveats. The README says LEGO cost varies with local availability, that the BOM cost is only a rough estimate, and that some parts may go out of stock because the BOM will not be actively maintained. Anyone attempting a build should expect to verify part numbers and quantities rather than ordering straight off the spreadsheet. The project is also young; it showed 26 stars on GitHub when this article was checked, which suggests there is not yet a large community of builders reporting fixes and variations.

For experienced makers, the more useful takeaway is the discipline of the constraint. Choosing a narrow parts vocabulary and documenting where it fails, as the journal does with the worm screws, the custom mounts, the Y-axis play and the extruder, is a good way to learn where a printer's precision really comes from.

Bottom Line

Studprint will not displace anyone's daily driver, and it does not claim to. It is a $173.35 machine that prints a Benchy in about 1.25 hours, built around a self-imposed LEGO rule that its own builder had to bend in the worm screws, the mounts and the extruder. With its CAD, BOM and build journal all public, it is an instructive open hardware project, and an open invitation for someone with a larger brick collection to see how far the idea can go.

Sources