Multicolor FDM printing has always charged a tax in plastic and time. Single-nozzle machines with filament changers purge a tower or a pile of "poop" at every swap, and toolchangers trade that waste for a gantry that picks up and drops heads mid-print. Co Print, a company best known for multicolor upgrade kits, is betting that a third layout can beat both. Its new Quadro printer mounts four independent toolheads on a single X-axis, and according to 3D Printing Industry's report on the launch, the all-or-nothing Kickstarter campaign has drawn more than $490,000 from roughly 600 backers against a goal of about $9,820, more than 46 times its target.

The campaign opened November 12 and runs through December 7, 2026. Co Print showed the machine at Formnext in Frankfurt the week of November 17 to 20. Reward tiers start at $649, which the company frames as $250 below a planned $899 retail price, and shipping is planned for February 2027. All specifications below are company-supplied, and the sources cited here include no independent test data.

How IQEX Works

Co Print calls the architecture IQEX, short for Independent Quad Extruder. Rather than a single carriage that grabs tools from a rack, Quadro puts four complete toolheads on one X-axis, and each head has its own stepper motor, belt and pulley. That makes it a close cousin of the IDEX (independent dual extruder) machines makers already know, stretched to four heads. No head ever has to be docked onto a shared carriage; a color change is just a matter of moving one head out of the way and another into position.

The company quotes mechanical switch times of 1.00 second from T1 to T2, 1.40 seconds to T3 and 1.57 seconds to T4. The spread makes physical sense: the farther a head sits from the active position, the longer the travel. Those are mechanical figures, not total layer-change overhead: Co Print itself notes that priming can add time depending on the job, and real-world gains will depend on how often a model swaps colors per layer.

Idle heads park in what Co Print calls QDock Stations. On the way to the dock a head retracts about 1 mm of filament and cools to around 140°C, and once parked its nozzle tip is sealed with a heat-resistant material. That combination is aimed squarely at the familiar IDEX failure modes: an idle nozzle dripping onto the bed or stringing across the part. To avoid a cold start, the next head begins heating about 30 seconds before it is needed, while the active head keeps printing.

Because the heads are independent, Quadro can also print two parts side by side. Heads 1 and 2 build one part while heads 3 and 4 build a second, so each part comes out in two colors, and the machine is not limited to acting as a single four-color printer.

The Spec Sheet

Build volume is 300 x 300 x 300 mm, on a 305 x 305 mm flexible steel sheet with a PEI surface, per Co Print's product page. The machine itself measures 780 x 620 x 515 mm, a footprint worth measuring for before ordering, since it is considerably larger than the build volume alone would suggest.

Advertisement
  • Toolheads: four, independently driven
  • Hotend: up to 300°C, hardened steel nozzles
  • Max speed: 600 mm/s
  • Max acceleration: 10,000 mm/s²
  • Max hotend flow: 24 mm³/s, tested with Co Print PLA Basic at 220°C
  • Firmware: QuadrOS, built on Klipper
  • Slicer: Co Slicer, open source, based on OrcaSlicer

The 24 mm³/s flow figure is the more useful number for estimating throughput; 600 mm/s is a ceiling that few real prints will reach with a single PLA head at that flow rate. Hardened steel nozzles as standard, combined with a 300°C hotend, suggest Co Print expects owners to run abrasive and engineering filaments, not just PLA.

The Waste Numbers, With Caveats

Co Print's headline claims are up to 70 percent shorter print times and up to 90 percent less waste. The company printed five four-color models on Quadro, a toolchanger and a large-format single-nozzle bed-slinger, using 0.4 mm nozzles and 0.2 mm layers on all three. Its football helmet model is the example it cites: on Quadro, 58.69 g of waste and a print time of 20 hours 36 minutes. The same model on the toolchanger produced 114.14 g of waste in 23 hours 40 minutes, and on the single-nozzle bed-slinger 301.4 g of waste in 1 day, 21 hours and 38 minutes.

Taken at face value, that is roughly half the toolchanger's waste and about 80 percent less than the single-nozzle machine, with print time cut by more than half against the bed-slinger. The comparison is the manufacturer's own, the competing machines are not named, and Co Print says results vary by model, material and print settings, so these figures are best read as a statement of intent rather than a benchmark.

Advertisement

Notably, Quadro does not claim zero waste in that test. When a head resumes printing, the machine typically builds a small prime tower to steady nozzle pressure. Co Print's optional Zero Waste Mode primes inside the model's infill instead, so no tower is needed, an approach that turns the leftover material into structure. It works only on compatible models with enough infill, and whether it stays clean on parts with sparse infill or thin walls is the kind of question early backers will answer.

Who Is Building It

Co Print is not new to multicolor printing, but it is new to building whole printers. The company has made multicolor upgrade kits since 2019, and its site still carries its Klipper-based KCM Set and Marlin-based ChromaSet kits. Its earlier MFM and ChromaSet crowdfunding campaigns delivered to more than 1,500 backers. Quadro is its first complete machine.

That history cuts both ways. A track record of shipping crowdfunded hardware is more than many Kickstarter printer projects can show. But an upgrade kit bolts onto a printer someone else designed, while a complete four-head machine means owning the frame, motion system, firmware and support burden at once.

What It Means for Makers

For makers who print multicolor parts regularly, Quadro's pitch is specific: four colors or materials without a purge tower in the best case, a toolchanger's waste profile without the docking mechanism, and side-by-side two-part printing as a bonus. The Klipper base and an OrcaSlicer-derived slicer mean the software stack should feel familiar, and Co Slicer is already open source. QuadrOS source, however, is promised only for later release, so anyone who cares about firmware openness should treat that as a pledge rather than a fact.

The usual crowdfunding cautions apply. The specs and waste figures are company-supplied, February 2027 is an ambitious window for a first complete printer, and backers are funding a pre-production design. The $649 tier is a real discount on the planned $899 MSRP, and Co Print's product page also lists a $574 early reservation price tied to a $20 deposit. For anyone who can wait, independent reviews after shipping will settle whether one-second color changes hold up in practice.

Sources