QIDI used Formnext 2026 to show its next enclosed desktop machine, and the pitch is aimed squarely at a problem every multi-material hobbyist knows. According to the QIDI Q3D product and pre-order page, the new printer pairs two independent nozzles with a 70C heated chamber, and the store lists it at $599. That price puts it in the same bracket as single-toolhead enclosed CoreXY machines, while promising something those machines handle badly: printing two materials without throwing away a pile of purged filament every time the color or polymer changes.

The Q3D is a CoreXY FDM printer on linear rails. 3D Printing Industry reports a toolhead speed of up to 600 mm/s, a quick-release main hotend rated to 350C, and an eddy-current sensor built into the hotend for bed leveling with no offset calibration required. The more interesting parts of the spec sheet, though, are the second nozzle and the chamber.

Why two nozzles instead of one

Most affordable multi-material setups today feed several spools into a single hotend. Every swap means retracting one filament, loading the next, and pushing enough plastic through the nozzle to flush the old material out. That flushed plastic ends up in a purge tower or a waste chute, and on a print with frequent changes it can add up to a lot of waste. It also costs time, since each swap involves a cut, a reload and a purge cycle.

QIDI's answer is the older one: give each material its own nozzle and do not let them share a filament path. The company says the Q3D's independent dual nozzles eliminate filament purging and claims multi-material print times drop by nearly half. That figure is a manufacturer claim, and the real saving will depend heavily on how many material changes a given model demands, but the direction is not in doubt. A dedicated nozzle can sit loaded and primed while the other one works.

The use case QIDI highlights most is supports. The product page says supports printed with a dedicated second nozzle snap off by hand. In practice that suggests a breakaway or interface material loaded in the second nozzle, which is a common technique for getting clean undersides on overhangs. With a single-nozzle changer, alternating materials at every support interface layer generates exactly the kind of purge waste the Q3D is designed to avoid.

A hot chamber for engineering filaments

The other headline feature is what QIDI calls a Gen-4 heated chamber, rated to 70C with dual air intake. Active chamber heating is the dividing line between an enclosed printer that merely shields prints from drafts and one that can reliably handle warp-prone polymers. Keeping the air around the part warm reduces the temperature gradient between fresh layers and the ones below, which is what drives warping and layer splitting in materials like ABS, ASA, nylon and polycarbonate.

The listed material range reflects that ambition. According to 3D Printing Industry, the Q3D's main hotend supports PLA, ABS, ASA, PETG, TPU, PA, PC and carbon- or glass-fiber-filled polymers. The 350C ceiling on the main hotend is high enough for the nylons and polycarbonates on that list, and the quick-swap bimetal nozzle QIDI describes, which changes without tools, should make it easier to switch nozzle sizes for different jobs.

Advertisement

Heat creates its own risk, since a hot chamber can soften filament before it reaches the melt zone and cause clogs. QIDI says the Q3D's extruder cooling duct cuts heat-related clog risk by up to 90 percent, again a vendor figure that will need independent testing. Filtration gets similar attention. A three-layer filter cartridge combines a G3 pre-filter, an H12 HEPA stage and coconut-shell activated carbon, and QIDI claims it captures 99.5 percent of dust, ultrafine particles and odors. For anyone printing ABS or ASA in a shared room or a home office, that matters more than a few extra millimeters per second.

Software, sensors and the fine print

The Q3D includes an AI camera, Wi-Fi and a filament runout sensor. Tangle detection requires QIDI's separate QIDI Box accessory. On the software side, 3D Printing Industry reports that the printer works with QIDI Studio, PrusaSlicer and Orca, though some advanced features are not supported outside QIDI's own slicer. Makers with established Orca or PrusaSlicer profiles should expect to use QIDI Studio for at least some dual-nozzle functions.

Advertisement

The spec tables on both pages list a 260 x 260 x 260 mm build volume for the main nozzle, while the auxiliary nozzle and dual-nozzle modes get 240 x 260 x 255 mm. Neither source states a maximum temperature for the second nozzle; the 350C figure applies to the main hotend. That second number matters for judging whether the Q3D can run a high-temperature material in both positions, so it is worth confirming before committing money.

Pricing and the presale offer

The pricing is easy to misread. QIDI's store lists the printer at $599 and offers a $100 credit toward it in exchange for a $30 presale payment, which the store says is fully refundable. The balance due is $499, and the store's own total, including the presale payment, is $529. That matches the $529 that 3D Printing Industry gives as the price after the $100 discount: $30 plus $499. The $100 discount applies to the $599 list price, but the deposit is counted inside the total rather than on top of it.

Delivery is not imminent. QIDI estimates shipping approximately three months after order placement and payment completion, and 3D Printing Industry puts it at about three months after an order is paid in full. Anyone paying the balance soon after the show is looking at delivery in early 2027 at the earliest.

What It Means for Makers

On paper, the Q3D lands in an attractive spot. Independent dual nozzles have historically been either expensive or fiddly, and the alternative most hobbyists use, a multi-spool feeder on a single hotend, trades upfront cost for ongoing waste. A sub-$600 enclosed CoreXY machine with a 70C chamber and a second dedicated nozzle would be a genuinely useful tool for two groups in particular: people who print functional parts in ASA, nylon or polycarbonate, and people who want soluble or breakaway supports without paying a purge-tower tax on every layer.

The caveats are the usual ones for a presale printer. The time savings, clog reduction and filtration figures are all QIDI's claims, the second nozzle's temperature limit is not stated in the material we reviewed, and full slicer support is tied to QIDI Studio. The three-month shipping window also leaves room for the final product to change. A $30 refundable deposit is a low-risk way to hold a place in line, but the sensible move is to wait for independent reviews of dual-nozzle alignment, chamber performance and print quality before paying the balance.

Sources