Most reinforced filaments get their stiffness from chopped glass or carbon fibre, and most makers know the price: worn brass nozzles and a practical limit on how small a nozzle the fibres will pass through. Otsuka Chemical's POTICON line takes a different approach, using ultra-fine potassium titanate whiskers sold under the TISMO name. A spool of the company's NTL34M polyamide grade recently landed in the hands of JanTec Engineering, which put it on a newly built testing machine. Hackaday's write-up of those tests gives an outside look at a material that, for now, is mostly found in industrial filaments. In short, the filament is strong and fine-grained, but it is also stiff and brittle, and the whiskers raise concerns of their own.

What POTICON Actually Is

According to Otsuka's own description, POTICON is a family of thermoplastic composites built around TISMO, the company's ultrafine potassium titanate fibre. Otsuka sells the additive as a micro-reinforcement. The company says it gives superior dimensional stability and is not aggressive on the materials it slides against, opening the path to grease-free products. It also says damage to molding machines and metal molds is minor and that the composite is highly recyclable.

The filament version is aimed at material-extrusion printing. Otsuka's filament datasheet page lists high dimensional accuracy, excellent surface smoothness, good sliding properties and low "nozzle aggressiveness" as the headline features. That last phrase is the one makers will care about most. JanTec received the STD1 NTL34M grade, which Hackaday notes is presumably PA6 and which the company calls LEXTER, a bio-based polyamide. It contains 20 percent TISMO by weight.

The Datasheet Numbers

Otsuka publishes a reasonably complete property sheet for NTL34M. The filament is white and measures 1.75 mm, plus or minus 0.05 mm. It has a density of 1.27 g/cm³ and a glass transition temperature of 60 °C.

The mechanical figures are split by print orientation, which is more honest than many filament datasheets manage. In the X-Y direction, Otsuka reports:

  • Tensile strength: 114 MPa
  • Elongation: 4.1 percent
  • Tensile modulus: 5.6 GPa
  • Flexural strength: 199 MPa
  • Flexural modulus: 7.0 GPa
  • Notched Izod impact: 32

In the Z-X direction, across layers, the numbers drop sharply. Tensile strength falls to 68 MPa, tensile modulus to 2.7 GPa and flexural strength to 107 MPa. The X-Y heat deflection temperature is 129.9 °C under a 0.45 MPa load and 104.8 °C at 1.80 MPa.

Otsuka attaches two caveats. The specimens were printed on a Gutenberg G-ZERO with a 0.4 mm nozzle, and the company calls the values representative rather than guaranteed. Anyone who has compared a manufacturer's lab-printed bars with parts from their own machine will read them that way.

Even so, the pattern in the data is telling. Tensile strength above 100 MPa with only 4.1 percent elongation describes a material that resists pulling well but stretches very little before it breaks. Tensile strength also drops by roughly 40 percent between the in-plane and cross-layer directions, a reminder that the whiskers, however fine, do nothing to bridge layer lines.

Advertisement

Putting It on the Rig

JanTec was handed the spool at an event in Japan and tested it after returning home, using the recommended print settings and a newly constructed testing machine called the Atlas 2000. Hackaday describes it as an open-source machine that could be handy if you have about $500 lying around and an urgent need to test the tensile, compression and bending properties of materials.

According to Hackaday, the filament scored well in the tensile strength test, while being about as brittle as the datasheet suggests. Hackaday adds that such reinforced polymers are generally known for being stiff and brittle, so this was little surprise. The brittleness of reinforced filaments is attributed to poor adhesion between the fibre or whisker and the thermoplastic. This is a familiar problem in filled plastics. When the reinforcement is not well bonded to the matrix, it can start cracks instead of stopping them.

The Fine-Nozzle Advantage

The most useful result comes from the size of the whiskers. They are much smaller and less abrasive than chopped glass or carbon fibre, and the filament works with 0.2 mm nozzles. Hackaday calls this perhaps the biggest advantage: you can print finer details with it, which makes it an interesting engineering filament.

Advertisement

A polyamide that is both stiff and able to hold fine detail is an unusual combination. Small gears, bushings and precision parts could benefit from a 0.2 mm nozzle, and Otsuka lists gears and mechanical parts among the filament's intended uses, along with its good sliding properties. The low elongation, however, suggests the material will be a poor fit for snap fits and flexures.

The Inhalation Question

JanTec's other point is less comfortable. The video touches on the potential health risks of this filament, because the whiskers are, in Hackaday's words, definitely easy to inhale. Hackaday compares this to the potential carcinogenic risks of chopped carbon fibre, where fragments of already small fibres can pose risks similar to asbestos. Commenters on the post were divided on how seriously to take it, and some said they would rather not print with it at all.

The sources do not say how much dust the filament sheds, so makers should judge the risk for themselves. Anyone who plans to sand, cut or grind finished parts should at least take the precautions they would use with glass- or carbon-filled parts: dust extraction, wet sanding where practical and a suitable respirator.

What It Means for Makers

POTICON NTL34M fills an interesting niche. Otsuka rates its in-plane tensile strength at 114 MPa and flexural strength at 199 MPa, and its heat deflection temperature at nearly 130 °C under light load. Its real advantage is the reinforcement itself. The whiskers are fine enough to work with a 0.2 mm nozzle, and Otsuka markets the filament on low nozzle aggressiveness.

The trade-offs are just as clear. Parts are stiff and brittle, with low elongation and a large loss of strength across layers, so print orientation matters a great deal. The brittleness appears to come from weak bonding between whisker and matrix, which print settings are unlikely to cure. The whiskers themselves also call for care during finishing.

Makers who need small, precise, rigid polyamide parts, especially sliding or wear components, should keep an eye on this material. For parts that must bend, absorb impact or survive abuse, a tougher unfilled or conventionally reinforced nylon is still the safer choice. JanTec's tests also point to something broader: with an open-source tester that costs about $500, independent makers can start checking materials for themselves.

Sources